橡胶补偿器CCS型式认可证书“中国船级社”
上海淞江减震器集团有限公司官方网站为您介绍：橡胶补偿器CCS型式认可证书“中国船级社”信息，上海淞江集团在2026年1月31日顺利通过了中国船级社CCS型式认证，并获得了中国船级社证书，我厂为众多船舶领域提供高品质橡胶补偿器，欢迎到我厂实地参观考察，也欢迎船舶领域各界领导到我厂指导工作。
声明：此证书不作为产品验收使用，我厂所有符合CCS标准的产品上面均有“CCS标识”及合格证明，请广大客户谨防假冒。
试验报告编号/ Test Report No. ： SJNT-CCSTA2601
试验报告日期/ Test Report Date ： 2026-01-13
试验单位/ Laboratory: 上海淞江减震器集团南通有限公司 Shanghai Songjiang Shock Absorber Group Nantong Co.,
Ltd.
试验单位地址/ Test Address: 江苏省南通市如东县双甸镇高前村5组 Group 5, Gaoqian Village, Shuangdian Town,
Rudong County, Nantong City, Jiangsu Province
按规范只认可不进行产品检验的产品/The product approved only in term of the rules：
认可后的产品由制造厂检验合格后签发合格证明，并连同该产品的本社认可证书复印件一并交付用户，制造厂对产
品符合公约、法规、本社规范和本社认可的标准规定负责。
After approval, product inspection should be carried out by the Manufacturer. Upon satisfactory
inspection, and the Quality Certificate issued by the Manufacturer should be provided to the
purchaser together with the copy of the approval certificate issued by the Society. The manufacturer
should take responsibility for the product being in compliance with the convention, statutory
regulation, the Society rules and the standard accepted by the Society.
1.型式认可后，如果产品及其重要零部件的设计、所用材料或制造方法有所改变，且影响到产品的主要特性、特
征；或产品的性能指标有所更改，且超过认可的范围，则有关图纸和文件应经检验机构审批。并在检验机构认为必
要时，经本社检验人员见证有关试验和进行检查，其结果应能证实仍符合认可条件。
After type approval, if there are changes to the design, materials used or manufacturing method of
the product and important components and such changes affect major characteristics and properties of
the product, or property indexes of the product are changed and exceed the scope of approval,
related drawings and documents are to be examined and approved by the concerned survey office. Where
deemed necessary by the survey office, the surveyor to the Society will go to witness relevant tests
and conduct inspection and the results should be able to demonstrate compliance with the approval
conditions.
2.工厂的质量管理体系应保持有效运行，并且与认可时一致。如果质量管理体系发生改变，应经原体系认证机构审
核并报本社批准。
The quality management system of the factory shall be ensure effective operation, and shall be the
same as the situation of approval. If there are any changes to the quality management system,
auditing of the original certification organization for quality management system and the society's
approval shall be obtained.
3.认可证书有效期内，如果出现可能导致本社取消认可的情况，工厂应及时采取有效的纠正措施。
Within the validity of the approval certificate, if cases occur that may cause the Society to
withdraw the approval, the manufacturer should take corrective actions in a prompt and effective
manner.
4.在认可证书有效期内，本社检验人员可在未经事先通知的情况下对工厂的产品制造过程进行审核，以验证产品的
生产是否符合业经本社批准的图纸和文件。工厂应予以配合。
Within the validity of the approval certificate, the surveyor to the Society may pay unannounced
audit to the manufacturing process of the product in order to confirm whether it is in compliance
with the drawings and documents approved by the Society. The factory should provide an active
cooperation and necessary for the surveyor.
5. 证书获得者应接受本社每年一次的定期审核，定期审核日为认可证书期满之日对应的每一周年日，检查工作应
在周年日的前后三个月内进行。
Those who have obtained the certificate should be subject to periodical audit every year. The date
of periodical audit shall be each anniversary date which corresponds to the date of expiry of the
relevant certificate and the periodical audit shall be done within a time span of three months
before and after the annual surveillance date.
1. 适用于以下船舶管系/Intended for the following marine piping systems:
空气、海水、淡水、润滑油、燃油及其它与补偿器材料相兼容的流体管系，用于润滑油、燃油等可燃介质及故障可
能导致进水的海水管系的补偿器应予以防火包覆，其包覆方式应与耐火试验一致/Air, SW，FW, LO, FO & other
liquid piping system in compatible with the compensator material. The compensators intended for LO,
FO & other flammable media or sea water systems where failure may result in flooding should be
covered by fireproof material and the covering method should be the same as that used in the fire
resistance test.
2. 补偿器的选用应视具体的服务要求，考虑使用的环境条件、工作压力、工作温度和介质的相容性/The
compensators are to be selected for the intended locations & applications which taken into
consideration of ambient conditions, compatibility with fluids under working pressure & temperature
conditions.
3. 补偿器应安装在具有足够照明和易于到达察看之处/The compensators are to be installed in clearly
visible and readily accessible locations.
4. 补偿器的选用应满足制造厂的使用说明要求/ The selection of the compensators are to be in compliance
with the instructions of the Manufacturer.
5. 本社已审核了产品厂无石棉声明，但本社的审核不免除产品厂按照合同关系向订货方保证产品无石棉的责任
/The declaration of asbestos-free submitted by manufacturer has been reviewed by the Society.
However, liability of the manufacturer to guarantee the products are asbestos-free to purchaser
under contract will not be exempted.
相关链接：美国ABS船级社证书
